2026-11-19
A two-point micrometer answers one question: what is the distance between two opposite points. A gauge is a three-dimensional object that has to slide over or into another three-dimensional object, and that interaction depends on shape, not just on the largest distance across.
This is why a gauge that measures perfectly can still behave badly, and why the measurement that satisfies a drawing can still produce a wrong verdict on the shop floor.
Ovality is a difference between the largest and smallest diameter of the same cross-section. A ring gauge that is 4.800 mm one way and 4.780 mm the other has a nominal diameter of 4.800 mm as far as the micrometer knows, and a 0.020 mm error in every other direction.
Taper is a change of diameter along the axis. A plug gauge that is correct at the entry and 0.01 mm small at the tip will start easily and then jam, which reads as a part problem.
Lobing is a three or five-lobed cross-section produced by centreless grinding. A two-point measurement across the lobes can read nominal while the effective diameter, the one that governs whether a part fits, is 0.005 to 0.015 mm smaller.
| Defect | Two-point reading | Effect on the verdict |
| Ovality 0.020 mm | Nominal | Rejects good parts in one orientation |
| Taper 0.010 mm over 20 mm | Nominal at entry | Starts, then jams; looks like a part fault |
| Lobing 0.010 mm | Nominal across lobes | Passes parts it should reject |
| Bell mouth 0.005 mm | Nominal at the ends | Feels right, wears fast |
For a gauge in a calibration programme, three measurements are worth more than thirty: diameter in three orientations 60 degrees apart, diameter at both ends of the working length, and a form check on a roundness tester or between centres with a dial indicator.
For a working gauge on the bench, one cheap check catches a surprising share of problems: rotate the gauge 90 degrees and repeat the same check. If the verdict changes with orientation, the gauge is not round.
The smaller the feature, the larger the relative effect. On a 4.8 mm pin, 0.010 mm of lobing is 0.2 % of the diameter and enough to flip a marginal judgement. On a 50 mm ring the same absolute error is 0.02 % and almost never decides anything.
Standards referenced: ISO 14253-1 for the decision rules when measurement uncertainty meets a tolerance, ISO 1101 for the form tolerances referenced on gauge drawings.
Most workshops do not have a roundness instrument, and most do not need one for this check. A V-block and a dial indicator will show lobing clearly: rotate the gauge through 360 degrees in a 90 degree V-block and read the indicator, which shows three-lobed form magnified about three times.
For ovality, a two-point measurement at 0, 45 and 90 degrees is enough. Three readings that differ by more than 0.005 mm mean the gauge is not round, and the largest reading is not the effective diameter.
For taper, measure at both ends of the working length. A difference of 0.008 mm over 20 mm is 0.04 % and enough to change how a close-fitting part behaves.
A plug gauge is used by inserting it, so taper and lobing matter more than ovality: lobing lets it enter a hole it should not. A ring gauge is used by passing it over a part, so ovality matters most: a slightly oval ring passes a slightly oval part in one orientation and rejects it in another.
A flat gauge, such as a depth or step gauge, is governed by flatness and parallelism, and a roundness check tells you nothing about it.
If a gauge shows lobing of 0.015 mm or more, it has usually been ground with a bad centreless setup and will keep producing the same form however often it is measured. Re-measuring costs a calibration; retiring costs a gauge. The second is cheaper than a wrong verdict repeated two hundred times.
Contact: Eason Wang
Phone: +86-13751010017
Tel: +86-755-33168386
Add: 1F Junfeng Building, Gongle, Xixiang, Baoan District, Shenzhen, Guangdong, China