Home   |   Technical Articles

Technical Articles

The Calibration Chain in a Gauge Room: From Gauge Blocks to a Working Go Gauge

2026-11-16

Every working gauge in a factory is a copy of a copy. Its size came from a setting master, which came from a gauge block set, which came from a national standard. Each transfer in that chain introduces uncertainty, and the discipline of a gauge room is mostly about making sure the uncertainty stays small enough that the gauge is still useful at the bottom of the chain.

The chain, named

  1. National standard. Realised in a metrology institute, with a stated uncertainty.
  2. Reference gauge blocks. Calibrated against the national standard, usually grade K or 0 to ISO 3650.
  3. Working gauge blocks. Grade 1 or 2, used daily. Grade 2 is adequate for most shop-floor work; grade 1 is what a gauge room should use for setting.
  4. Setting master or setting plug. A stable artefact used to set adjustable gauges or to check fixed ones.
  5. Working gauge. The go plug, the thread ring, the snap gauge that actually touches product.

A part measured with the working gauge carries the uncertainty of every link above it. That is why the answer to "how accurate is this gauge" is never a single number.

The 1:4 rule and why it is not optional

The working rule is that the calibration uncertainty of a gauge should be no more than one quarter of the tolerance it is used to inspect. On a part with a 0.02 mm band, the gauge's uncertainty contribution should be within 0.005 mm. On a 0.05 mm band, 0.0125 mm.

The rule exists because uncertainties combine. If the gauge contributes a quarter of the band and the measurement process contributes another quarter, the inspection is still meaningful. If the gauge contributes half the band, a part at the middle of tolerance has a genuine chance of being called good or bad on the gauge alone, and the resulting argument cannot be settled with more inspections — only with a better chain.

Part toleranceGauge uncertainty budgetChain that fits
0.20 mm0.050 mmGrade 2 blocks, shop-floor gauge
0.05 mm0.0125 mmGrade 1 blocks, calibrated setting master
0.01 mm0.0025 mmGrade 0 blocks, comparator, temperature control

Temperature is the largest term most rooms ignore

Steel expands by about 11.5 micrometres per metre per kelvin. On a 100 mm gauge, a 5 K difference from the reference temperature moves the reading by roughly 5.75 micrometres — more than half the uncertainty budget of the 0.01 mm row in the table above. The reference temperature is 20 degrees C, and the rule that follows is that the gauge, the master and the workpiece must all be at 20 degrees C, not merely "in the room".

A 100 mm steel gauge and a 100 mm aluminium workpiece at the same air temperature are not the same size. Aluminium expands at roughly twice the rate of steel, so a workpiece that soaked at 25 degrees C and a gauge that soaked at 20 degrees C differ by about 11 micrometres on 100 mm before either is measured. Soak time matters more than air temperature: a 100 mm steel block needs roughly an hour to settle after a 10 K change, and a large casting needs far longer.

Wringing, and the air gap that is not zero

Gauge blocks are wrung together to build a size. A properly wrung stack has an interface film of the order of 0.01 to 0.02 micrometres, which is negligible on most work but should be in the budget when the stack is long. Two practical rules:

  • Wring with clean hands and clean blocks; a single particle of grit is thicker than the film and holds the blocks apart.
  • Build the stack from the largest block down, using the fewest blocks that reach the size. Each additional interface adds uncertainty and a place for error.

What the record should contain

A calibration certificate that says "within tolerance" is not traceability. The record needs the measured value, the uncertainty, the reference temperature, the standard used and the identification of the master. Without the measured value, a drift trend cannot be built, and drift is what predicts the next failure.

Two habits make the chain auditable:

  1. Record the as-found value before adjustment. The as-found number is the evidence that the previous interval was adequate.
  2. Record the as-left value after adjustment, with the adjustment made. A gauge that needed 8 micrometres of adjustment every cycle is telling you the interval is too long, even though every certificate says pass.

For the artefacts themselves, the gauge and test equipment range includes setting masters and wear-check accessories; the site index links the calibration accessories used with them.

close
Scan the qr codeClose
the qr code